What is HVAC?

HVAC stands for "heating, ventilating, and air-conditioning". It is alternately referred to as "climate control". Heating, ventilating, and air-conditioning improve the quality of indoor air, provide temperature control, and control the flow of air throughout your home.

What SEER means?

SEER or Seasonal Energy Efficiency Ratio ratings are established by the U. S. Department of Energy (DOE).

What is AFUE? 

AFUE is the abbreviation for Annual Fuel Utilization Efficiency ratio. AFUE is used to rate furnace efficiencies by dividing the ratio of heat output by heat input. This measurement describes how well fuel, gas or oil is consumed to produce heat by a furnace. As the AFUE rate increases, the efficiency of your furnace also increases, lowering your fuel costs. Furnaces manufactured in the United States are required to have at least an 80% AFUE.

What is HSPF? 

HSPF is the abbreviation for the Heating Seasonal Performance Factor, which is a rating of the efficiency level of the heating operation of a heat pump. The higher the HSPF, the more efficient the heating performance of a heat pump. New units in the United States have HSPF ratings from 7.0 to 9.4.

What is R-22? 

R-22 is the common name for hydro-chlorofluorocarbon (HCFC). R-22 has been used as a refrigerant by HVAC manufacturers for over 40 years, but studies in the past decade have shown that HCFCs contain chlorine, an ozone-depleting agent. For this reason, the United States Clean Air Act has set a target date for January 1, 2010, on which HVAC manufacturers must cease the production of products that use R-22.  

What is R-410A? 

R-410A is the common name for an emerging hydro-fluorocarbon (HFC) that is being used as a refrigerant in the HVAC industry. R-410A is more environmentally friendly than R-22 and is being seen as the most likely replacement for R-22 by HVAC manufacturers. Effective January 2010, HVAC manufacturers no longer produce air conditioning and heat pump products that use R-22 refrigerant.

Why should I purchase a new heating or air conditioning system?   

Efficiency and cost savings!  If your existing system is old, in need of repair or simply inefficient, purchasing a new unit, one which can be as much as 60% more efficient than a system purchased just 10 years ago, can offer long-term benefits. Rather than continuing to pay for ongoing maintenance and costly monthly bills, invest in a new system today that will save you money for years to come. 

How can I find the system that’s right for me?  

The size and age of your home, as well as the number of rooms, climate, and local and regional utility costs are all factors that will affect the functionality and, therefore, selection of your system. Consumers seeking to replace an existing system often choose a new unit with equal or higher efficiency ratings compared to their previous system. Replacing a unit that is 10- to 15-years-old may reduce natural gas or electricity costs by 30 to 50%.

Contact us to help determine initial cost, warranty protection, service options, maintenance options, operating cost and proper installation. You can also get a copy of the product warranty from any dealer. 

How do I determine the size, or capacity, of my HVAC system?  

Schedule a visit. Factors affecting the size of your new system include the climate in your region, humidity levels, the number of windows in your dwelling, total square footage of your home, the direction your home faces, the number of heat-producing appliances in your home, the type of insulation you have and the number of people that live in your residence.

What goes into installing a new system?  

It’s all about the ductwork. Putting a new system in a home that has not had central air and heat before will require the installation of ductwork, insulation, refrigerant piping, electrical service, wiring, thermostat, condensate piping, flue piping, flue terminations, chimney liner, slabs, filter, driers, registers, grills, drain pans and evaporator coil. Beyond equipment, the most important component installed with a new system, however, is the ductwork.

Ductwork is composed of two parts, supply and return. Supply duct is attached to the outflow of the new system, delivering air to each zone in a home. The amount of air reaching each zone is determined by the size of supply ductwork connecting it to your system. The return duct, attaches to the inlet of the new system and draws air out of the spaces to be heated or cooled. Attached to the return duct is the filter. The filter should be placed as near to the furnace or air handler as possible. Ductwork can be either fiberglass or metal and must be properly sized in order to evenly distribute the proper amount of air to each room. 

How long will my system last?   

Proper maintenance is key. Maintenance and service play a key role in the life-cycle of a heating or air conditioning system. If all recommended maintenance and service actions are taken, an air conditioner can last 12 to 15 years and a gas furnace 20 to 25 years.

Do I need to change my indoor coil?

It is generally a good idea to replace the indoor coil if you are also replacing your air conditioner or heat pump. There is a correlation between the efficiency of your heating or cooling system and the performance of the indoor coil and changing out the current indoor coil for a new one may be critical to optimizing the performance, the efficiency and the savings potential of your new system.

Where can I locate my air handler or furnace system?  

You may have options based on your home’s design. The system can actually be located in several different places. A system with up-flow application might be located in the basement, while a system with a horizontal application may be found in your attic. A self-contained, or single package unit, could be located outside on a slab or on the roof. Your garage could house an up-flow, down-flow or horizontal application system.

What is a heat pump?  

Air movement from point A to point B. A heat pump is a device used for either the heating or cooling of a space by transferring hot and cold between two reservoirs. It can act like an air conditioner, transferring heat from inside to out, or like a heater as it transfers exterior heat to the interior. A winter day with a temperature of 32º Fahrenheit still produces enough heat to warm a space when the air is transferred by heat pump.

What can I do to control the humidity levels in my home? 

It’s all about variability. Humidity levels can be reduced by using a variable-speed furnace or air handler as part of your HVAC system. Variable speed units run longer, at lower speeds, allowing air to constantly circulate against the cooling coil and remove more moisture. Variable-speed motors also use less electricity than regular motors, reducing your energy costs.

What can I do before calling someone to service my system?  

HVAC systems are complicated networks of machinery that should be serviced by a certified professional. However, if your HVAC system seems to be malfunctioning, you can try a few basic steps, which may correct your problem, prior to calling a service professional. If you do not feel comfortable performing any of these tasks, however, do not hesitate to call.

 •Disconnect and reconnect your indoor and outdoor switches. 

•Make sure your circuit breakers are in the ON position.

•Make sure your filters are clean.

•Open supply and return vents and make sure they are unobstructed.

•Check the settings on your thermostat.

•Make sure the system switch is on the appropriate COOL or HEAT setting.